Skip to content
My Repair Store

MacBook won't turn on? What to check first

A MacBook that won't turn on is often a flat battery, a faulty charger or a Mac that is running with a dark screen, not a dead logic board. Work through the checks below in order. If none of them brings it back, the fault is usually on the logic board or in the power circuit, and that needs a technician.

Quick checks you can do at home

  1. Charge it for a while. Plug in the charger that came with the Mac (or one with the same or higher wattage) and leave it connected for at least 15 minutes before you try again. A fully drained battery can take a few minutes before the Mac will start.
  2. Swap the charger and cable. Try a different USB-C cable and power adapter if you have them, and a different wall socket. Check the cable along its length and at both ends for kinks, fraying or burn marks. On a MagSafe 3 Mac, look at the light on the connector: no light means no power is reaching the Mac.
  3. Try every port. If your Mac charges over USB-C, try each USB-C port in turn. Remove any hub, dock or adapter and connect the charger directly.
  4. Check whether it is actually on. Press Caps Lock and see whether the key light comes on, press the brightness-up key a few times, and listen near the vents for a fan on Intel models. If there are signs of life, the problem may be the display rather than the power.
  5. Test with an external display. Connect a monitor or TV with the right adapter. If a picture appears there, the Mac is starting and the fault is in the built-in screen or its cable. See our guide to display cable faults for some older MacBook Pro models.
  6. Force a restart. Press and hold the power button (Touch ID button on newer models) for about 10 seconds, release it, wait a few seconds, then press it once.
  7. Reset the power controller. The steps depend on which chip your Mac has. See the next section.

Power resets: Apple silicon vs Intel

Intel MacBooks have a System Management Controller (SMC) that looks after charging, power and the fans. Resetting it clears a stuck power state. Macs with Apple silicon (M1 and later) have no separate SMC, so there is nothing to reset in the same way.

  • Apple silicon (M1, M2, M3, M4 and later): with the charger connected, press and hold the power button for 10 seconds to make sure it is fully off, wait at least 30 seconds, then press the power button once.
  • Intel MacBook with the T2 security chip (most 2018–2020 models): shut down. Press and hold Control and Option on the left and Shift on the right for 7 seconds, then also press and hold the power button. Keep all four held for another 7 seconds, release, wait a few seconds and turn it on.
  • Older Intel MacBook without T2: shut down, then hold Shift, Control and Option on the left side together with the power button for 10 seconds. Release and turn it on.

If you are not sure which chip you have, the Apple menu › About This Mac shows it, but only once the Mac starts. See MacBook repair for the models we work on. Apple's own steps for a Mac that won't start are on Apple Support.

What each result means

  • It started after charging or a new cable: the battery was flat or the old charger or cable is faulty. Stop using the faulty one.
  • It works on the external display only: the logic board is running; the built-in display, its backlight or its cable has failed.
  • Caps Lock lights up but nothing else happens: the Mac is getting power but is not finishing startup. A software or firmware problem is possible, as is a logic board fault.
  • No light, no sound, nothing with two known-good chargers: the fault is most likely in the charging circuit or on the logic board.
  • It turns on only while plugged in: the battery may be worn out or disconnected. Check battery health once it starts, in System Settings › Battery.

An advanced note: revive or restore with Apple Configurator

On Apple silicon Macs and Intel Macs with the T2 chip, a damaged firmware update can leave the Mac unable to start. Apple's fix is to connect it to a second Mac running Apple Configurator and put it into DFU mode. A revive reinstalls the firmware and recovery system and is designed to keep your data. A restore erases the Mac completely. The key combinations are specific to each model and the process needs the right USB-C cable, so only try it if you are comfortable with it, and never run a restore on a Mac whose data you have not backed up.

When to stop and get it repaired

  • The Mac has had liquid on it, even a small amount. Do not keep trying to power it on; follow our liquid spill guide.
  • You notice a burning smell, the charger or the bottom case gets hot, or the case or trackpad looks raised. A raised trackpad can mean a swollen battery.
  • It stopped working after a drop or a knock.
  • None of the checks above made any difference.

Get it checked

When a MacBook shows no sign of life with a known-good charger, the cause is usually on the logic board: a failed power chip, a short circuit or damage from liquid. Our diagnosis is free, and we tell you what we found before any work starts. See MacBook logic board repair, or book a diagnosis.

Need it fixed? See MacBook logic board repair, or send us a message. Diagnosis is free.

FAQ

Questions

If my MacBook won't turn on, is my data lost?

Not necessarily. Most power faults are in the charging circuit or on the logic board, and the data stays on the storage until the Mac is repaired. On Apple silicon and most T2 Macs the storage is part of the logic board and encrypted, so the board has to work again to read it. Avoid running a restore in Apple Configurator, which erases the Mac, until you know your data is backed up.

My MacBook makes no startup sound. Does that mean it is dead?

No. MacBooks from 2016 to 2019 were sold with the startup sound turned off, and on newer Macs it can be switched off in System Settings › Sound. Check for other signs of life instead: the Caps Lock light, the keyboard backlight, a fan on Intel models, or a picture on an external display.

How do I reset the SMC on an M1, M2 or M3 MacBook?

You can't, because Apple silicon Macs have no separate System Management Controller. Its jobs are handled by the chip itself. The equivalent is to shut the Mac down fully, wait at least 30 seconds and turn it back on, with the charger connected if the battery may be flat. If that does not help, the fault is probably not something a reset can clear.