Skip to content
My Repair Store

MacBook Pro Flexgate: stage-light effect and backlight cutting out

Flexgate is a display cable fault in 13-inch and 15-inch MacBook Pro models from 2016 and 2017. The thin cables that carry the backlight signal through the hinge wear out from opening and closing the lid, causing uneven light along the bottom of the screen and then a backlight that cuts out past a certain lid angle. The fix is a display repair, not software.

Which models are affected

Flexgate is associated with the first Touch Bar-era MacBook Pro design, where the display flex cables are short and wrap tightly around the hinge:

MacBook Pro models associated with Flexgate
ModelYearModel number
MacBook Pro 13-inch, Two Thunderbolt 3 ports2016, 2017A1708
MacBook Pro 13-inch, Four Thunderbolt 3 ports2016, 2017A1706
MacBook Pro 15-inch2016, 2017A1707

Apple ran a Display Backlight Service Program for some 13-inch MacBook Pro 2016 models. It applied for a limited period after the original sale, so these Macs are now outside it, but you can check Apple's current programmes on Apple Support. Later models use a revised cable design. A dim or flickering screen on a 2018 or newer MacBook, or on any MacBook Air, usually has a different cause.

Quick checks you can do at home

  1. Confirm your model. Go to the Apple menu › About This Mac. It should say MacBook Pro (13-inch, 2016 or 2017) or MacBook Pro (15-inch, 2016 or 2017). The model number, such as A1706, is printed in small text on the bottom case.
  2. Look at the bottom of the screen. Open a plain white or light grey page at full brightness. Flexgate often starts as the "stage-light" effect: brighter patches alternating with darker areas along the bottom edge, like spotlights at the front of a stage.
  3. Open the lid slowly. Start with the lid half open, then open it further a little at a time. If the backlight goes off past a certain angle and comes back when you close it slightly, the cable is the likely cause.
  4. Try the torch test. When the screen looks black, shine a phone torch at it from close up. If you can faintly see the desktop, the display panel is working and only the backlight is off.
  5. Connect an external display. If the image is normal on a monitor, the Mac itself is fine and the fault is in the display assembly.
  6. Rule out software. Restart, check that brightness is up, and turn off automatic brightness in System Settings › Displays to see whether anything changes. Software will not cause the angle-dependent cut-out, but it is worth ruling out.

What each result means

  • Stage-light effect only: the cable is starting to wear. It usually gets worse over time.
  • Backlight cuts out past an angle: the cable is partly broken. Many people keep the lid at a narrow angle to use the Mac, which is a short-term workaround only.
  • Backlight off at every angle, image visible with a torch: the backlight cable or circuit has failed fully.
  • Lines, colour faults or cracks on the screen: that is panel damage, not Flexgate, though the repair can be similar.

Why it happens

On these models, the display flex cables are part of the display assembly and run around the hinge. Every time you open and close the lid, they bend. Because they are short, they are under tension near full opening, and over years of use the fine tracks in them crack. The backlight signal is usually the first to fail, which is why the picture is still there but not lit.

When to stop and get it repaired

Once the backlight starts cutting out, opening the lid wider keeps stressing the damaged cable. If you depend on the Mac, back up your data now while it is still usable, ideally with an external display connected. Get it looked at before the screen stops working at every angle.

How it is repaired

Because the cables are attached to the panel, the usual fix is a display assembly replacement. We check the model and test the backlight circuit on the logic board first, so you know whether the board also needs work. Diagnosis is free and we confirm the part grade and price before starting. See MacBook screen replacement or message us on WhatsApp.

Need it fixed? See MacBook screen replacement, or send us a message. Diagnosis is free.

FAQ

Questions

Which MacBooks are affected by Flexgate?

Flexgate is associated with the 13-inch MacBook Pro from 2016 and 2017 (A1706 and A1708) and the 15-inch MacBook Pro from 2016 and 2017 (A1707). Apple used a revised cable design from 2018. You can check your model in the Apple menu › About This Mac, or by reading the model number printed on the bottom case.

Can I keep using my MacBook Pro with the lid only half open?

For a short while, yes, but it is a workaround, not a fix. The damaged cable carries on wearing every time the lid moves, and it will eventually fail at every angle. Use an external display where you can, back up your data, and plan the repair before the built-in screen stops working completely.

Can a software update fix Flexgate?

No. Flexgate is physical wear in the display flex cables that run through the hinge, so no macOS update or setting can repair it. If your screen dims or flickers in the same way at every lid angle, a software or brightness setting is worth ruling out, but a backlight that cuts out past a certain angle is a hardware fault.